Bissell Steam Mop Not Steaming? 8 Fixes That Work

Quick answer

Most Bissell steam mops that “won’t steam” just need more time: after the ready light turns solid blue and you choose a steam setting, the pump can knock for up to 2 minutes before steam flows. If it still doesn’t steam, check that the tank has water, is seated with no gaps, isn’t cracked, and that the cap’s rubber gasket is in place. Use only water in the tank. Then remove and refit the foot so it clips in at the back, and with the mop unplugged, clean the spray tip under the foot with a paperclip. If there’s still no steam, contact Bissell.

These steps follow Bissell’s own support guidance for the PowerFresh Steam Mop (models 1940, 19401, 1940M and related), the most common Bissell steam mop. Other Bissell models work similarly, but check your user guide for model-specific details.

Upright steam mop with a microfiber pad on a kitchen tile floor

First: is it really not steaming?

Bissell points out that you won’t see an abundance of steam from a PowerFresh because the steam is directed down into the pad and floor (BISSELL: No Steam, PowerFresh). A damp pad and a moist streak on the floor mean it’s working. Lift the mop briefly and look at the pad: if it’s warm and damp, the mop is steaming.

Bissell PowerFresh steam mop not steaming: causes and fixes in order

8 fixes for a Bissell steam mop not steaming

1. Wait for the heater and the pump

Plug the mop in and wait for the ready light: Bissell says it blinks blue for about 30 seconds, then stays on. Then select a steam setting. You’ll hear knocking while the pump pulls water through; Bissell says this can take up to 2 minutes, and it happens on first use, each time the tank runs dry, and after the mop has sat unused. The knocking should change to a muffled hum once water reaches the pump (BISSELL: PowerFresh knocking noise).

2. Check the outlet and the ready light

If the ready light never comes on, try another outlet you know works. If the light still won’t turn on, the heater isn’t getting power and the mop needs service.

3. Fill and reseat the water tank

Make sure there’s water in the tank and that it sits fully in place with no gaps. A tank that’s even slightly out of position can’t feed the pump.

4. Inspect the tank for cracks and leaks

Bissell suggests checking the tank in a well-lit room, with water in it, for cracks or drips. A cracked tank needs replacing.

5. Check the cap and its rubber gasket

The tank cap has a rubber gasket at its tip. If the cap is cracked or the gasket is missing, water won’t feed correctly. Replace the cap.

6. Use only water

Bissell says it’s very important to use only water in the PowerFresh tank, because other solutions can break down the gasket and other parts. If you’ve added vinegar, scented oils or cleaner, rinse the tank thoroughly with tap water and refill with water only. Also avoid filling it with very hot water, which can deform the tank so it doesn’t seat properly.

7. Remove and refit the foot

The foot should lock in at the back with a clip and sit flush against the body with no gaps. Take it off and click it back on.

8. Clear the spray tip

Turn off and unplug the mop. Remove the foot and use a paperclip to clean the spray tip at the bottom of the body where the foot attaches. Plug it in with the foot off and test for steam, keeping hands and face away from the tip. If it steams without the foot but not with it, Bissell says to order a new foot; if there’s no steam at all, contact Bissell (BISSELL: No steam in the foot).

How to prevent it happening again

  • Fill with water only, and never add fragrance or cleaner to the tank.
  • Empty the tank after use so water doesn’t sit in the mop for weeks.
  • Wash or replace dirty microfiber pads; a clogged pad blocks steam from reaching the floor.
  • If you have very hard water, check your user guide for Bissell’s water recommendation for your model.

Using the mop on the right floors matters too: see steam mops on vinyl and steam mops on laminate. If your problem is a Bissell carpet cleaner that won’t spray rather than a steam mop, see our Bissell carpet cleaner guide.

Frequently asked questions

Why is my Bissell steam mop making a knocking noise but not steaming?

That’s the pump pulling water through. Bissell says it can take up to 2 minutes, especially on first use or after the tank ran dry. If it knocks longer, reseat the tank and restart.

Can I put vinegar in my Bissell steam mop?

Not in the PowerFresh. Bissell says to use only water, since other solutions can damage the gasket and other parts.

Why is my Bissell PowerFresh 2-in-1 not steaming?

The same checks apply: wait for the heater and pump, check the tank and cap, use water only, and clear the spray tip. Follow the user guide for your exact model.

How do I unclog a Bissell steam mop?

Unplug it, remove the foot and clean the spray tip with a paperclip. If it still won’t steam, contact Bissell support.

Why is steam coming out of the side instead of the bottom?

Check that the foot is clipped on flush with no gaps. If steam still escapes from the body, contact Bissell, especially if the mop is under warranty.

Sources

Related guides